| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Zero mailbox struct in qla2x00_get_firmware_state()
The mbx_cmd_t is allocated on the stack but left uninitialized.
qla2x00_mailbox_command() has several early-return paths (PCI permanent
failure, device failed, EEH busy, ISP abort pending, mailbox access
timeout, purge mbox) that return without writing the input mailbox
registers back into mcp->mb[]. qla2x00_get_firmware_state() then
unconditionally copies mcp->mb[1..6] (and mb[12]) into the caller's
states[] array regardless of the return value.
On such a failure the copied values are uninitialized kernel stack
memory, which is then exposed to userspace via the fw_state and
mpi_fw_state sysfs handlers. Zero the mailbox struct so a failed query
yields deterministic zeroed state instead of leaking stack contents. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix cs84xx use-after-free on host teardown
qla84xx_put_chip() drops the last reference to ha->cs84xx and frees it via
__qla84xx_chip_release() without clearing ha->cs84xx. During teardown it ran
before scsi_remove_host(), which is what removes the 84xx_fw_version host
sysfs attribute. A concurrent read of that attribute in the window between
the two calls executes qla24xx_84xx_fw_version_show(), which dereferences
the freed ha->cs84xx, resulting in a use-after-free.
Move qla84xx_put_chip() to after scsi_remove_host() in both
qla2x00_remove_one() and qla2x00_disable_board_on_pci_error(). Once
scsi_remove_host() returns, the sysfs attribute is gone and kernfs has
drained any in-flight show(), so no reader can touch cs84xx; the put still
runs before the host and ha are freed. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Zero dport diagnostics buffer to avoid info leak
qla2x00_do_dport_diagnostics() allocates the qla_dport_diag response
buffer with kmalloc_obj() (non-zeroing) and, on success, copies the full
sizeof(*dd) back to user space via sg_copy_from_buffer(). The inbound
sg_copy_to_buffer() only fills as many bytes as the user request payload
provides, and qla26xx_dport_diagnostics() zeroes only dd->buf. The
options and unused[] fields are therefore copied out uninitialized,
leaking kernel heap contents to user space.
Allocate with kzalloc_obj(), matching qla2x00_do_dport_diagnostics_v2(). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Initialize NVMe abort_work once at submission
qla_nvme_fcp_abort() and qla_nvme_ls_abort() ran INIT_WORK() on
priv->abort_work immediately before schedule_work(). INIT_WORK()
reinitializes the work_struct, resetting its list head and clearing the
pending bit. If an abort is issued more than once for the same command
(for example, concurrent transport teardown and a timeout-driven abort),
the second INIT_WORK() reinitializes a work item that is already queued,
which can corrupt the workqueue list and lead to crashes or a looping
worker.
Initialize priv->abort_work once at command submission, next to the
existing per-command spin_lock_init(&priv->cmd_lock), and leave only
schedule_work() in the abort paths. schedule_work() already does nothing
when the work item is still pending, so a repeated abort no longer
disturbs an in-flight work item. The command is not returned to the
transport until the final kref_put()/release callback runs after
abort_work has completed, so the work item is idle before priv is reused
and the single submission-time INIT_WORK() is safe. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: edif: Fix NULL pointer deref in RX SA delete check
qla_chk_edif_rx_sa_delete_pending() obtains the SCSI command via
GET_CMD_SP(sp) and immediately dereferences cmd->sc_data_direction.
That command pointer can be NULL: the firmware may post a status
completion for a command that has already been returned or aborted. The
caller qla2x00_status_entry() acknowledges this on the very same status
path, re-fetching GET_CMD_SP(sp) and bailing out with the "Command
already returned" message when it is NULL -- but that check runs only
after qla_chk_edif_rx_sa_delete_pending() has already dereferenced the
pointer, so a NULL cmd crashes the kernel in interrupt context.
Return early when cmd is NULL, before touching cmd->sc_data_direction. |
| In the Linux kernel, the following vulnerability has been resolved:
media: chips-media: wave5: Resume device before setting EOS flag
Setting the EOS flag talks to the firmware via send_firmware_command(),
which accesses VPU registers. Both the STREAMOFF path
(wave5_vpu_dec_job_abort()) and the V4L2_DEC_CMD_STOP path
(wave5_vpu_dec_stop()) can run while the device is runtime suspended, so
those register accesses hit powered-down hardware and the SoC raises an
asynchronous SError, panicking the kernel:
SError Interrupt on CPU3, code 0x00000000bf000000 -- SError
send_firmware_command+0x2c/0x160 [wave5]
wave5_vpu_dec_set_bitstream_flag+0x6c/0x80 [wave5]
wave5_vpu_dec_update_bitstream_buffer+0x80/0xec [wave5]
wave5_vpu_dec_job_abort+0x44/0xa0 [wave5]
v4l2_m2m_cancel_job+0x110/0x19c [v4l2_mem2mem]
v4l2_m2m_streamoff+0x24/0x140 [v4l2_mem2mem]
Resume the device with pm_runtime_resume_and_get() around the EOS
firmware command and release it with pm_runtime_put_autosuspend(),
matching the runtime PM handling already done in
wave5_vpu_dec_device_run(). |
| In the Linux kernel, the following vulnerability has been resolved:
media: chips-media: wave5: Defer job_finish() only when a DEC_PIC was queued
Decoder instances sharing a VPU also share one v4l2_m2m job slot, released
when the running context calls v4l2_m2m_job_finish(). While draining,
device_run() defers job_finish() once EOS is sent (sent_eos), expecting a
later finish_decode() (from a DEC_PIC completion IRQ) to release the slot.
But the m2m core checks job_ready() only when a job is queued, not when it
is dispatched. A job queued while draining can run after finish_decode()
has already moved the instance to STOP and sent EOS. device_run() then runs
in STOP, issues no DEC_PIC, yet still skips job_finish() - so no IRQ, no
finish_decode(), and the shared slot is leaked, stalling every instance.
With several v4l2h264dec instances in parallel, GStreamer hangs at EOS.
Track whether the run actually queued a DEC_PIC (cmd_issued) and defer
job_finish() only then. Otherwise finish the job immediately |
| In the Linux kernel, the following vulnerability has been resolved:
media: qcom: iris: use disable_irq() during power-off
The IRQ is registered as a threaded IRQ.
Using disable_irq_nosync() in iris_vpu_power_off() does not wait
for an already queued threaded IRQ handler to complete before
returning.
As a result, a threaded IRQ handler may still run after the VPU has
been powered down and access hardware registers after power-off.
Replace disable_irq_nosync() with disable_irq() so the power-off path
waits for any in-flight threaded IRQ handler to complete before
returning. |
| In the Linux kernel, the following vulnerability has been resolved:
media: video-i2c: fix kthread error pointer left in kthread_vid_cap on failure
kthread_run() returns an ERR_PTR on failure, not NULL.
When start_streaming() fails, data->kthread_vid_cap is left holding
this error pointer instead of being cleared.
This causes two subsequent bugs:
1. A future call to start_streaming() sees a non-NULL kthread_vid_cap
and returns 0 (success) immediately, without actually starting the
capture thread.
2. A call to stop_streaming() checks 'kthread_vid_cap == NULL' which
is false for an error pointer, and proceeds to call kthread_stop()
on the error pointer, leading to a kernel crash.
Fix this by resetting kthread_vid_cap to NULL on failure before
jumping to the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
media: s2255: check firmware size before reading trailing marker
s2255_probe() reads a 4-byte marker and version from the last 8 bytes
of the firmware blob (fw->data[fw_size - 8] and [fw_size - 4]). If the
firmware file is shorter than 8 bytes, fw_size - 8 underflows and the
access reads out of bounds. Validate the firmware size before indexing. |
| In the Linux kernel, the following vulnerability has been resolved:
media: rtl2832_sdr: use vb2_video_unregister_device() on remove to fix DMA leak
rtl2832_sdr_remove() runs on USB disconnect and clears dev->udev to
NULL before any pending streaming teardown has run. When user space
later closes its file descriptor, vb2 calls rtl2832_sdr_stop_streaming()
which in turn calls rtl2832_sdr_free_stream_bufs(). That helper releases
each coherent buffer with:
usb_free_coherent(dev->udev, dev->buf_size,
dev->buf_list[dev->buf_num],
dev->dma_addr[dev->buf_num]);
usb_free_coherent() returns immediately when its dev argument is NULL,
so every DMA stream buffer that was live at disconnect is silently
leaked. The URBs allocated in rtl2832_sdr_alloc_urbs() outlive the
device for the same reason.
The rtl2832_sdr driver uses vb2_fop_release() in its file_operations,
so replace video_unregister_device(&dev->vdev) with
vb2_video_unregister_device(&dev->vdev) and move it before clearing
dev->udev. vb2_video_unregister_device() releases the vb2 queue, which
synchronously runs rtl2832_sdr_stop_streaming() if streaming is active,
so URBs and coherent DMA stream buffers are freed while dev->udev is
still valid.
vb2_video_unregister_device() locks vdev->queue->lock (vb_queue_lock)
internally, and stop_streaming() locks v4l2_lock, so the previous outer
mutex_lock(&dev->vb_queue_lock) / mutex_lock(&dev->v4l2_lock) pair
around the unregister sequence would self-deadlock and has been removed.
A short v4l2_lock critical section around dev->udev = NULL remains so
any ioctl path that still holds the file descriptor sees coherent state.
Issue identified by automated review of the INV-003 series at
https://sashiko.dev/ |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: rawnand: validate ONFI extended parameter page sections
nand_flash_detect_ext_param_page() allocates the length declared by the
ONFI parameter page, then treats the data as a fixed header followed by
variable-length sections. It reads that header and advances over sections
without first proving that the fixed page and each current section fit in
the allocation.
Reject pages shorter than the fixed header, track the remaining variable
area while walking sections, and require the ECC section to contain every
field read from struct onfi_ext_ecc_info. Use device-scoped diagnostics
that identify the malformed ONFI section. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-tcp: fix out-of-bounds write when receiving an over-long PDU
nvmet_tcp_try_recv_pdu() reads a PDU header into the fixed 128-byte
queue->pdu union, then computes the remaining payload length as
queue->left = hdr->hlen - queue->offset + hdgst;
and reads that many more bytes into &queue->pdu + queue->offset, without
ever bounding the result against sizeof(queue->pdu).
A struct nvme_tcp_icreq_pdu is itself 128 bytes, exactly the size of the
union. Once a header digest has been negotiated (hdgst = 4), a second
ICReq passes the hlen == nvmet_tcp_pdu_size() check but yields
queue->left = 128 - 8 + 4 = 124, so bytes 8..132 are written into the
128-byte buffer -- 4 bytes past its end, over queue->hdr_digest and
queue->data_digest. Those bytes are attacker-controlled (an ICReq
carries no digest), and the duplicate ICReq is only rejected later,
after the overflow. A remote unauthenticated host can thus corrupt
kernel memory adjacent to the receive buffer.
Reject any PDU whose declared length would read past the end of
queue->pdu before the second recv. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Fix kernel address leakages in LBR stack
Before Arch LBR gained CPL filtering support, a user-only branch stack
could still contain kernel addresses. As a result, kernel branch records
may be exposed to user space even when PERF_SAMPLE_BRANCH_USER is
requested.
For example, on Intel Tiger Lake, the following command can still report
SYSRET/ERET entries with kernel-space from addresses:
$ ./perf record -e cycles:p -o - --branch-filter any,save_type,u -- \
./perf bench syscall basic --loop 1000 | \
./perf script -i - --fields brstack|tr ' ' '\n'| \
grep -E '0x[89a-f][0-9a-f]{15}'
Total time: 0.000 [sec]
0.219000 usecs/op
4,566,210 ops/sec
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.551 MB - ]
0xffffffff93c001c8/0x7f12a2b1d647/P/-/-/16959/SYSRET/-
0xffffffff93c001c8/0x7f12a2b1d5c2/P/-/-/17535/SYSRET/-
0xffffffff93c01928/0x7f12a2861000/P/-/-/6719/ERET/-
0xffffffff93c01928/0x7f12a297a000/P/-/-/8575/ERET/-
The problem is that intel_pmu_lbr_filter() does not fully validate the
privilege level of sampled entries. It filters some mismatches based on
the branch type and the to address, but it does not reject entries whose
from address violates the requested branch privilege filter.
Fix this by extending software filtering to validate both from and to
addresses against br_sel. Any LBR entry contains kernel address does not
match the requested user filter is dropped. This prevents kernel
addresses from appearing in user-only branch stacks. |
| In the Linux kernel, the following vulnerability has been resolved:
cpuidle: dt_idle_genpd: kfree() the original name allocation
dt_idle_pd_alloc() kasprintf()s the full node path, then points
pd->name at kbasename() of that string. dt_idle_pd_free() kfree()s
pd->name, which is no longer the start of the allocation.
Copy the basename instead. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: qcom-pmic-typec: disable cc_debounce_dwork on stop
cc_debounce_dwork is queued from the set_cc() and start_toggling()
callbacks, which run from TCPM's kthread worker. port_stop() returns
before tcpm_unregister_port() destroys that worker. Flushing the worker
during unregister may therefore run a callback which queues the delayed
work after port_stop() has returned.
The delayed work can then run after devres has freed pmic_typec_port.
Use disable_delayed_work_sync() in port_stop() to cancel a pending
instance and prevent the TCPM callbacks from queueing another one.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: clear forceRM when issuing EndTransfer
The forceRM bit of the DEPCMD register controls the behavior of the
EndTransfer command used to stop an active transfer. Older DWC3
programming guide revisions recommended setting forceRM=1 when
issuing EndTransfer. Newer programming guide revisions recommend
issuing EndTransfer with forceRM cleared.
With forceRM=1 on DWC_usb31 v2.00a and v2.10a controllers, a transfer
aborted through the ep_dequeue path was observed to remain active
after EndTransfer completion. A subsequent StartTransfer issued on the
same endpoint triggered writes associated with the aborted transfer.
This resulted in an SMMU fault because the transfer buffer had already
been unmapped during EndTransfer command-completion cleanup.
Using forceRM=0 eliminates the issue. Although older DWC3 programming
guide revisions recommended setting forceRM=1, no issues are known
from using forceRM=0. Clear forceRM when issuing EndTransfer to provide
consistent EndTransfer behavior and align with newer programming guide
recommendations. |
| An improper certificate validation vulnerability in Email API in Synology DiskStation Manager (DSM) before 7.2.1-69057-10, 7.2.2-72806-7 and 7.3.2-86009-2 allows man-in-the-middle attackers to read or write arbitrary files and conduct denial-of-service attacks. |
| An improper restriction of excessive authentication attempts vulnerability in Auto block in Synology DiskStation Manager (DSM) before 7.2.1-69057-10, 7.2.2-72806-7 and 7.3.2-86009-2 allows remote attackers to read limited files via brute-force attacks. |
| An improper limitation of a pathname to a restricted directory ('path traversal') vulnerability in Desktop API in Synology DiskStation Manager (DSM) before 7.2.1-69057-10, 7.2.2-72806-7 and 7.3.2-86009-2 allows remote attackers to write limited files and conduct limited denial-of-service attacks. |
