| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: strictly check for maximum number of actions
The maximum number of flowtable hardware offload actions in IPv6 is:
* ethernet mangling (4 payload actions, 2 for each ethernet address)
* SNAT (4 payload actions)
* DNAT (4 payload actions)
* Double VLAN (4 vlan actions, 2 for popping vlan, and 2 for pushing)
for QinQ.
* Redirect (1 action)
Which makes 17, while the maximum is 16. But act_ct supports for tunnels
actions too. Note that payload action operates at 32-bit word level, so
mangling an IPv6 address takes 4 payload actions.
Update flow_action_entry_next() calls to check for the maximum number of
supported actions.
While at it, rise the maximum number of actions per flow from 16 to 24
so this works fine with IPv6 setups. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Properly mark live registers for indirect jumps
For a `gotox rX` instruction the rX register should be marked as used
in the compute_insn_live_regs() function. Fix this. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: define and enforce CEPH_MAX_KEY_LEN
When decoding the key, verify that the key material would fit into
a fixed-size buffer in process_auth_done() and generally has a sane
length.
The new CEPH_MAX_KEY_LEN check replaces the existing check for a key
with no key material which is a) not universal since CEPH_CRYPTO_NONE
has to be excluded and b) doesn't provide much value since a smaller
than needed key is just as invalid as no key -- this has to be handled
elsewhere anyway. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: prevent races in ->query_interfaces()
It was possible for two query interface works to be concurrently trying
to update the interfaces.
Prevent this by checking and updating iface_last_update under
iface_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Add SRCU protection for reading PDPTRs in __get_sregs2()
Add SRCU read-side protection when reading PDPTR registers in
__get_sregs2().
Reading PDPTRs may trigger access to guest memory:
kvm_pdptr_read() -> svm_cache_reg() -> load_pdptrs() ->
kvm_vcpu_read_guest_page() -> kvm_vcpu_gfn_to_memslot()
kvm_vcpu_gfn_to_memslot() dereferences memslots via __kvm_memslots(),
which uses srcu_dereference_check() and requires either kvm->srcu or
kvm->slots_lock to be held. Currently only vcpu->mutex is held,
triggering lockdep warning:
=============================
WARNING: suspicious RCU usage in kvm_vcpu_gfn_to_memslot
6.12.59+ #3 Not tainted
include/linux/kvm_host.h:1062 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by syz.5.1717/15100:
#0: ff1100002f4b00b0 (&vcpu->mutex){+.+.}-{3:3}, at: kvm_vcpu_ioctl+0x1d5/0x1590
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xf0/0x120 lib/dump_stack.c:120
lockdep_rcu_suspicious+0x1e3/0x270 kernel/locking/lockdep.c:6824
__kvm_memslots include/linux/kvm_host.h:1062 [inline]
__kvm_memslots include/linux/kvm_host.h:1059 [inline]
kvm_vcpu_memslots include/linux/kvm_host.h:1076 [inline]
kvm_vcpu_gfn_to_memslot+0x518/0x5e0 virt/kvm/kvm_main.c:2617
kvm_vcpu_read_guest_page+0x27/0x50 virt/kvm/kvm_main.c:3302
load_pdptrs+0xff/0x4b0 arch/x86/kvm/x86.c:1065
svm_cache_reg+0x1c9/0x230 arch/x86/kvm/svm/svm.c:1688
kvm_pdptr_read arch/x86/kvm/kvm_cache_regs.h:141 [inline]
__get_sregs2 arch/x86/kvm/x86.c:11784 [inline]
kvm_arch_vcpu_ioctl+0x3e20/0x4aa0 arch/x86/kvm/x86.c:6279
kvm_vcpu_ioctl+0x856/0x1590 virt/kvm/kvm_main.c:4663
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl fs/ioctl.c:893 [inline]
__x64_sys_ioctl+0x18b/0x210 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xbd/0x1d0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query
Fix a "scheduling while atomic" bug in mlx5e_ipsec_init_macs() by
replacing mlx5_query_mac_address() with ether_addr_copy() to get the
local MAC address directly from netdev->dev_addr.
The issue occurs because mlx5_query_mac_address() queries the hardware
which involves mlx5_cmd_exec() that can sleep, but it is called from
the mlx5e_ipsec_handle_event workqueue which runs in atomic context.
The MAC address is already available in netdev->dev_addr, so no need
to query hardware. This avoids the sleeping call and resolves the bug.
Call trace:
BUG: scheduling while atomic: kworker/u112:2/69344/0x00000200
__schedule+0x7ab/0xa20
schedule+0x1c/0xb0
schedule_timeout+0x6e/0xf0
__wait_for_common+0x91/0x1b0
cmd_exec+0xa85/0xff0 [mlx5_core]
mlx5_cmd_exec+0x1f/0x50 [mlx5_core]
mlx5_query_nic_vport_mac_address+0x7b/0xd0 [mlx5_core]
mlx5_query_mac_address+0x19/0x30 [mlx5_core]
mlx5e_ipsec_init_macs+0xc1/0x720 [mlx5_core]
mlx5e_ipsec_build_accel_xfrm_attrs+0x422/0x670 [mlx5_core]
mlx5e_ipsec_handle_event+0x2b9/0x460 [mlx5_core]
process_one_work+0x178/0x2e0
worker_thread+0x2ea/0x430 |
| In the Linux kernel, the following vulnerability has been resolved:
net: consume xmit errors of GSO frames
udpgro_frglist.sh and udpgro_bench.sh are the flakiest tests
currently in NIPA. They fail in the same exact way, TCP GRO
test stalls occasionally and the test gets killed after 10min.
These tests use veth to simulate GRO. They attach a trivial
("return XDP_PASS;") XDP program to the veth to force TSO off
and NAPI on.
Digging into the failure mode we can see that the connection
is completely stuck after a burst of drops. The sender's snd_nxt
is at sequence number N [1], but the receiver claims to have
received (rcv_nxt) up to N + 3 * MSS [2]. Last piece of the puzzle
is that senders rtx queue is not empty (let's say the block in
the rtx queue is at sequence number N - 4 * MSS [3]).
In this state, sender sends a retransmission from the rtx queue
with a single segment, and sequence numbers N-4*MSS:N-3*MSS [3].
Receiver sees it and responds with an ACK all the way up to
N + 3 * MSS [2]. But sender will reject this ack as TCP_ACK_UNSENT_DATA
because it has no recollection of ever sending data that far out [1].
And we are stuck.
The root cause is the mess of the xmit return codes. veth returns
an error when it can't xmit a frame. We end up with a loss event
like this:
-------------------------------------------------
| GSO super frame 1 | GSO super frame 2 |
|-----------------------------------------------|
| seg | seg | seg | seg | seg | seg | seg | seg |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
-------------------------------------------------
x ok ok <ok>| ok ok ok <x>
\\
snd_nxt
"x" means packet lost by veth, and "ok" means it went thru.
Since veth has TSO disabled in this test it sees individual segments.
Segment 1 is on the retransmit queue and will be resent.
So why did the sender not advance snd_nxt even tho it clearly did
send up to seg 8? tcp_write_xmit() interprets the return code
from the core to mean that data has not been sent at all. Since
TCP deals with GSO super frames, not individual segment the crux
of the problem is that loss of a single segment can be interpreted
as loss of all. TCP only sees the last return code for the last
segment of the GSO frame (in <> brackets in the diagram above).
Of course for the problem to occur we need a setup or a device
without a Qdisc. Otherwise Qdisc layer disconnects the protocol
layer from the device errors completely.
We have multiple ways to fix this.
1) make veth not return an error when it lost a packet.
While this is what I think we did in the past, the issue keeps
reappearing and it's annoying to debug. The game of whack
a mole is not great.
2) fix the damn return codes
We only talk about NETDEV_TX_OK and NETDEV_TX_BUSY in the
documentation, so maybe we should make the return code from
ndo_start_xmit() a boolean. I like that the most, but perhaps
some ancient, not-really-networking protocol would suffer.
3) make TCP ignore the errors
It is not entirely clear to me what benefit TCP gets from
interpreting the result of ip_queue_xmit()? Specifically once
the connection is established and we're pushing data - packet
loss is just packet loss?
4) this fix
Ignore the rc in the Qdisc-less+GSO case, since it's unreliable.
We already always return OK in the TCQ_F_CAN_BYPASS case.
In the Qdisc-less case let's be a bit more conservative and only
mask the GSO errors. This path is taken by non-IP-"networks"
like CAN, MCTP etc, so we could regress some ancient thing.
This is the simplest, but also maybe the hackiest fix?
Similar fix has been proposed by Eric in the past but never committed
because original reporter was working with an OOT driver and wasn't
providing feedback (see Link). |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: kaweth: remove TX queue manipulation in kaweth_set_rx_mode
kaweth_set_rx_mode(), the ndo_set_rx_mode callback, calls
netif_stop_queue() and netif_wake_queue(). These are TX queue flow
control functions unrelated to RX multicast configuration.
The premature netif_wake_queue() can re-enable TX while tx_urb is still
in-flight, leading to a double usb_submit_urb() on the same URB:
kaweth_start_xmit() {
netif_stop_queue();
usb_submit_urb(kaweth->tx_urb);
}
kaweth_set_rx_mode() {
netif_stop_queue();
netif_wake_queue(); // wakes TX queue before URB is done
}
kaweth_start_xmit() {
netif_stop_queue();
usb_submit_urb(kaweth->tx_urb); // URB submitted while active
}
This triggers the WARN in usb_submit_urb():
"URB submitted while active"
This is a similar class of bug fixed in rtl8150 by
- commit 958baf5eaee3 ("net: usb: Remove disruptive netif_wake_queue in rtl8150_set_multicast").
Also kaweth_set_rx_mode() is already functionally broken, the
real set_rx_mode action is performed by kaweth_async_set_rx_mode(),
which in turn is not a no-op only at ndo_open() time. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: pci: validate release report content before using for RTL8922DE
The commit 957eda596c76
("wifi: rtw89: pci: validate sequence number of TX release report")
does validation on existing chips, which somehow a release report of SKB
becomes malformed. As no clear cause found, add rules ahead for RTL8922DE
to avoid crash if it happens. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: fix 22000 series SMEM parsing
If the firmware were to report three LMACs (which doesn't
exist in hardware) then using "fwrt->smem_cfg.lmac[2]" is
an overrun of the array. Reject such and use IWL_FW_CHECK
instead of WARN_ON in this function. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix missing key size check for L2CAP_LE_CONN_REQ
This adds a check for encryption key size upon receiving
L2CAP_LE_CONN_REQ which is required by L2CAP/LE/CFC/BV-15-C which
expects L2CAP_CR_LE_BAD_KEY_SIZE. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nSVM: Always use vmcb01 in VMLOAD/VMSAVE emulation
Commit cc3ed80ae69f ("KVM: nSVM: always use vmcb01 to for vmsave/vmload
of guest state") made KVM always use vmcb01 for the fields controlled by
VMSAVE/VMLOAD, but it missed updating the VMLOAD/VMSAVE emulation code
to always use vmcb01.
As a result, if VMSAVE/VMLOAD is executed by an L2 guest and is not
intercepted by L1, KVM will mistakenly use vmcb02. Always use vmcb01
instead of the current VMCB. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: tracepoints: get correct superblock from dentry in event btrfs_sync_file()
If overlay is used on top of btrfs, dentry->d_sb translates to overlay's
super block and fsid assignment will lead to a crash.
Use file_inode(file)->i_sb to always get btrfs_sb. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_set_pipapo_avx2: don't return non-matching entry on expiry
New test case fails unexpectedly when avx2 matching functions are used.
The test first loads a ranomly generated pipapo set
with 'ipv4 . port' key, i.e. nft -f foo.
This works. Then, it reloads the set after a flush:
(echo flush set t s; cat foo) | nft -f -
This is expected to work, because its the same set after all and it was
already loaded once.
But with avx2, this fails: nft reports a clashing element.
The reported clash is of following form:
We successfully re-inserted
a . b
c . d
Then we try to insert a . d
avx2 finds the already existing a . d, which (due to 'flush set') is marked
as invalid in the new generation. It skips the element and moves to next.
Due to incorrect masking, the skip-step finds the next matching
element *only considering the first field*,
i.e. we return the already reinserted "a . b", even though the
last field is different and the entry should not have been matched.
No such error is reported for the generic c implementation (no avx2) or when
the last field has to use the 'nft_pipapo_avx2_lookup_slow' fallback.
Bisection points to
7711f4bb4b36 ("netfilter: nft_set_pipapo: fix range overlap detection")
but that fix merely uncovers this bug.
Before this commit, the wrong element is returned, but erronously
reported as a full, identical duplicate.
The root-cause is too early return in the avx2 match functions.
When we process the last field, we should continue to process data
until the entire input size has been consumed to make sure no stale
bits remain in the map. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: validate bsscfg indices in IF events
brcmf_fweh_handle_if_event() validates the firmware-provided interface
index before it touches drvr->iflist[], but it still uses the raw
bsscfgidx field as an array index without a matching range check.
Reject IF events whose bsscfg index does not fit in drvr->iflist[]
before indexing the interface array.
[add missing wifi prefix] |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: tighten UMEM headroom validation to account for tailroom and min frame
The current headroom validation in xdp_umem_reg() could leave us with
insufficient space dedicated to even receive minimum-sized ethernet
frame. Furthermore if multi-buffer would come to play then
skb_shared_info stored at the end of XSK frame would be corrupted.
HW typically works with 128-aligned sizes so let us provide this value
as bare minimum.
Multi-buffer setting is known later in the configuration process so
besides accounting for 128 bytes, let us also take care of tailroom space
upfront. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: Wait for RCU readers during policy netns exit
xfrm_policy_fini() frees the policy_bydst hash tables after flushing the
policy work items and deleting all policies, but it does not wait for
concurrent RCU readers to leave their read-side critical sections first.
The policy_bydst tables are published via rcu_assign_pointer() and are
looked up through rcu_dereference_check(), so netns teardown must also
wait for an RCU grace period before freeing the table memory.
Fix this by adding synchronize_rcu() before freeing the policy hash tables. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: handle wraparound when searching for blocks for indirect mapped blocks
Commit 4865c768b563 ("ext4: always allocate blocks only from groups
inode can use") restricts what blocks will be allocated for indirect
block based files to block numbers that fit within 32-bit block
numbers.
However, when using a review bot running on the latest Gemini LLM to
check this commit when backporting into an LTS based kernel, it raised
this concern:
If ac->ac_g_ex.fe_group is >= ngroups (for instance, if the goal
group was populated via stream allocation from s_mb_last_groups),
then start will be >= ngroups.
Does this allow allocating blocks beyond the 32-bit limit for
indirect block mapped files? The commit message mentions that
ext4_mb_scan_groups_linear() takes care to not select unsupported
groups. However, its loop uses group = *start, and the very first
iteration will call ext4_mb_scan_group() with this unsupported
group because next_linear_group() is only called at the end of the
iteration.
After reviewing the code paths involved and considering the LLM
review, I determined that this can happen when there is a file system
where some files/directories are extent-mapped and others are
indirect-block mapped. To address this, add a safety clamp in
ext4_mb_scan_groups(). |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: don't irele after failing to iget in xfs_attri_recover_work
xlog_recovery_iget* never set @ip to a valid pointer if they return
an error, so this irele will walk off a dangling pointer. Fix that. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix type confusion in l2cap_ecred_reconf_rsp()
l2cap_ecred_reconf_rsp() casts the incoming data to struct
l2cap_ecred_conn_rsp (the ECRED *connection* response, 8 bytes with
result at offset 6) instead of struct l2cap_ecred_reconf_rsp (2 bytes
with result at offset 0).
This causes two problems:
- The sizeof(*rsp) length check requires 8 bytes instead of the
correct 2, so valid L2CAP_ECRED_RECONF_RSP packets are rejected
with -EPROTO.
- rsp->result reads from offset 6 instead of offset 0, returning
wrong data when the packet is large enough to pass the check.
Fix by using the correct type. Also pass the already byte-swapped
result variable to BT_DBG instead of the raw __le16 field. |
