| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
media: rkvdec: hevc: guard INTER_REF_PIC_SET_PRED index underflow
st_ref_pic_set_prediction() computes the reference RPS index as
st_rps_idx - (delta_idx_minus1 + 1) per HEVC spec equation 7-59.
Both operands are u8, so when delta_idx_minus1 + 1 exceeds the
current index the subtraction wraps and the subsequent array access
at calculated_rps_st_sets[ref_rps_idx] reads far out of bounds.
A userspace V4L2 client that can open the RKVDEC m2m decoder can
submit an EXT_SPS_ST_RPS control with INTER_REF_PIC_SET_PRED set
and delta_idx_minus1 crafted to trigger the underflow.
Reject the entry early when the reference index would underflow. |
| In the Linux kernel, the following vulnerability has been resolved:
media: rtl2832_sdr: release URBs and stream buffers on start_streaming() failure
rtl2832_sdr_start_streaming() calls rtl2832_sdr_alloc_stream_bufs(),
rtl2832_sdr_alloc_urbs() and rtl2832_sdr_submit_urbs() in sequence and
shares a single err: label that only unlocks the mutex and returns.
When alloc_urbs() succeeds but submit_urbs() fails, or when alloc_urbs()
itself returns -ENOMEM after alloc_stream_bufs() has already succeeded,
the URBs and/or the coherent DMA stream buffers stay allocated while
streaming reports failure to vb2. Two latent defects follow on the next
VIDIOC_STREAMON:
1) rtl2832_sdr_alloc_stream_bufs() unconditionally resets dev->buf_num
to 0 and overwrites dev->buf_list[]/dev->dma_addr[], permanently
leaking the coherent DMA memory allocated by the previous attempt.
2) rtl2832_sdr_alloc_urbs() never resets dev->urbs_initialized and only
increments it. After a second successful pass urbs_initialized can
exceed MAX_BULK_BUFS, so the subsequent rtl2832_sdr_free_urbs() walks
from urbs_initialized - 1 down to 0 and reads past the end of
dev->urb_list[], passing garbage pointers to usb_free_urb().
Mirror the teardown that stop_streaming() already performs: on the error
path call rtl2832_sdr_free_urbs() and rtl2832_sdr_free_stream_bufs()
before unlocking. Both helpers are idempotent (free_urbs kills and zeros
urbs_initialized; free_stream_bufs is gated on URB_BUF and clears the
buf_num counter), so partial-failure paths and the no-allocation paths
remain safe.
Issue identified by automated review of the INV-003 series at
https://sashiko.dev/ |
| In the Linux kernel, the following vulnerability has been resolved:
media: saa7164: fix cleanup on resource allocation failure
saa7164_dev_setup() adds the device to the global saa7164_devlist before
requesting the PCI BAR memory regions.
If get_resources() fails, saa7164_dev_setup() decrements the device count
and returns an error, but leaves the device on saa7164_devlist. The probe
error path then frees the device, leaving a dangling entry on the global
list.
Reuse the existing MMIO mapping error path to remove the device from
saa7164_devlist and decrement the device count before returning.
Also release BAR0 if it was successfully requested but the BAR2 request
fails. |
| In the Linux kernel, the following vulnerability has been resolved:
media: ti: vpe: quiesce overflow recovery before freeing streams
The VIP overflow recovery worker is armed from the hardirq handler when a
FIFO overflow is detected, and the list-complete path looks the stream up
through the VPDMA list private pointer. Both keep touching stream, port
and device state; the recovery worker also resets the parser and VPDMA,
repopulates the descriptor list, and re-enables the per-list IRQs.
vip_stop_streaming() masks and clears the per-list IRQs, but it neither
synchronizes the hardirq handler nor disables recovery_work. An overflow
IRQ that has already queued recovery_work, or a list-complete IRQ in
flight when the stream is torn down, can therefore still dereference the
stream after its resources are released: the descriptor list is freed by
vip_release_stream() on file release, and the stream itself by
free_stream() on unbind/remove.
Drain the recovery worker and the IRQ handler at both teardown points
through a shared vip_quiesce_stream() helper, before any stream-owned
resource is released. disable_work_sync() cancels pending recovery_work,
drains a running instance, and raises its disable depth, so a subsequent
schedule_work() issued by a racing IRQ handler is rejected at the
workqueue scheduler: recovery_work cannot be requeued after
disable_work_sync() takes effect. The worker may still re-enable the
per-list IRQs before disable_work_sync() returns; disable_irqs() then
masks those sources and synchronize_irq() waits for any in-flight handler
that still dereferences stream state. In vip_stop_streaming() the helper
runs before the parser is stopped, since a worker drained by
disable_work_sync() may re-enable the parser before exiting and would
otherwise undo the stop. recovery_work is created disabled and enabled in
vip_start_streaming() before IRQs, pairing the enable with the teardown
disable across the streaming lifecycle.
This issue was found by an in-house static analysis tool and confirmed
by manual code review. |
| In the Linux kernel, the following vulnerability has been resolved:
media: v4l2-ctrls: validate HEVC EXT SPS RPS counts
The HEVC SPS control carries the short-term and long-term RPS counts
that decoder drivers use to walk the matching EXT SPS dynamic arrays.
Reject SPS values that exceed the HEVC limits of 64 short-term sets and
32 long-term references so drivers cannot later index beyond those
controls.
Also reject EXT SPS ST RPS entries whose negative or positive picture
counts exceed the 16-entry arrays, or whose combined delta-POC count
exceeds the HEVC DPB maximum. |
| In the Linux kernel, the following vulnerability has been resolved:
media: zoran: Avoid freeing a registered video_device twice
zoran_init_video_device() installs zoran_vdev_release() as the
video_device release callback through zoran_template. After
video_register_device() succeeds, video_unregister_device() drops the
registered video_device reference and the V4L2 core eventually invokes
that release callback, which kfree()s the video_device.
zoran_exit_video_devices() called video_unregister_device() and then
kfree(zr->video_dev), so device teardown could free the same
video_device twice.
Remove the direct kfree() and clear the cached pointer after
unregistering. The pre-registration failure path keeps its manual free
because the video_device was not registered there.
This issue was found by a static analysis checker and confirmed by
manual source review. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: edif: Fix NULL pointer deref in RX SA delete check
qla_chk_edif_rx_sa_delete_pending() obtains the SCSI command via
GET_CMD_SP(sp) and immediately dereferences cmd->sc_data_direction.
That command pointer can be NULL: the firmware may post a status
completion for a command that has already been returned or aborted. The
caller qla2x00_status_entry() acknowledges this on the very same status
path, re-fetching GET_CMD_SP(sp) and bailing out with the "Command
already returned" message when it is NULL -- but that check runs only
after qla_chk_edif_rx_sa_delete_pending() has already dereferenced the
pointer, so a NULL cmd crashes the kernel in interrupt context.
Return early when cmd is NULL, before touching cmd->sc_data_direction. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Hold vport reference in qla24xx_report_id_acquisition()
In the format 1 path, the virtual port is located on ha->vp_list while
holding vport_slock, but the lock is dropped before vp is used:
qla_update_host_map() is called and VP_IDX_ACQUIRED/REGISTER_FC4_NEEDED/
REGISTER_FDMI_NEEDED are set on vp. No reference is taken across that
window, so a concurrent qla24xx_deallocate_vp_id() can tear the vport
down and free it, leading to a use-after-free.
Take a vport reference (vref_count) under vport_slock when the matching
vp is found, and drop it after the last use of
vp. qla24xx_deallocate_vp_id() waits for vref_count to reach zero before
unlinking and freeing the vport, so the pointer stays valid. This
matches the reference idiom already used by the other ha->vp_list
traversals. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Initialize NVMe abort_work once at submission
qla_nvme_fcp_abort() and qla_nvme_ls_abort() ran INIT_WORK() on
priv->abort_work immediately before schedule_work(). INIT_WORK()
reinitializes the work_struct, resetting its list head and clearing the
pending bit. If an abort is issued more than once for the same command
(for example, concurrent transport teardown and a timeout-driven abort),
the second INIT_WORK() reinitializes a work item that is already queued,
which can corrupt the workqueue list and lead to crashes or a looping
worker.
Initialize priv->abort_work once at command submission, next to the
existing per-command spin_lock_init(&priv->cmd_lock), and leave only
schedule_work() in the abort paths. schedule_work() already does nothing
when the work item is still pending, so a repeated abort no longer
disturbs an in-flight work item. The command is not returned to the
transport until the final kref_put()/release callback runs after
abort_work has completed, so the work item is idle before priv is reused
and the single submission-time INIT_WORK() is safe. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Hold qpair lock when sending NVMe LS reject
qla_nvme_ls_reject_iocb() allocates from and advances the request ring
through __qla2x00_alloc_iocbs() (which assumes the hardware_lock is
held) and qla2x00_start_iocbs() (which advances the ring and rings the
request-in doorbell), but takes no lock itself. Two of its callers
invoke it without the producer lock held:
- qla_nvme_xmt_ls_rsp(), the NVMe-FC .xmt_ls_rsp transport callback, on
its error path, and
- qla2xxx_process_purls_pkt(), run from the purex work/DPC context.
Both use ha->base_qpair, whose qp_lock_ptr is hardware_lock, so they can
run concurrently with normal I/O submission on the base ring and corrupt
the ring producer state, leading to duplicated or dropped commands. The
third caller, qla2xxx_process_purls_iocb(), runs inside
qla24xx_process_response_queue() with the qpair lock already held and is
safe; that is also why the lock cannot be taken inside the helper itself
(it would recursively re-acquire hardware_lock on the response path).
Take qp_lock_ptr around the two unlocked callers and document the helper
as caller-locked. Both run in process context, so spin_lock_irqsave() is
used and nothing in the locked region sleeps. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Clamp MSI-X derived queue counts to avoid truncation
ha->msix_count is u16, but ha->max_req_queues, ha->max_rsp_queues and
ha->max_qpairs are u8. Deriving the queue count as
"ha->max_req_queues = ha->msix_count - 1" therefore truncates: a board
(or a misconfigured/malicious hot-plugged device) advertising 257 MSI-X
vectors yields msix_count - 1 == 256, which truncates to 0. An MSI-X
count of 1 zeroes it as well, and in target mode the subsequent
"ha->max_req_queues--" then underflows 0 to 255.
When the count is 0, qla2x00_alloc_queues() calls
kzalloc_objs(struct req_que *, 0), which returns ZERO_SIZE_PTR. That is
not NULL, so the allocation check passes and the following
"ha->req_q_map[0] = req" dereferences ZERO_SIZE_PTR, corrupting memory
or crashing the kernel.
Add qla_calc_queue_count() to clamp the derived value into
[1, QLA_MAX_QUEUES - 1] so it always fits in u8 and is never zero, and
use it at all three derivation sites (qla25xx_iospace_config(),
qla83xx_iospace_config() and qla24xx_enable_msix()). Also guard the
target-mode decrement so it cannot reintroduce a zero (which would in
turn underflow max_qpairs). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix cs84xx use-after-free on host teardown
qla84xx_put_chip() drops the last reference to ha->cs84xx and frees it via
__qla84xx_chip_release() without clearing ha->cs84xx. During teardown it ran
before scsi_remove_host(), which is what removes the 84xx_fw_version host
sysfs attribute. A concurrent read of that attribute in the window between
the two calls executes qla24xx_84xx_fw_version_show(), which dereferences
the freed ha->cs84xx, resulting in a use-after-free.
Move qla84xx_put_chip() to after scsi_remove_host() in both
qla2x00_remove_one() and qla2x00_disable_board_on_pci_error(). Once
scsi_remove_host() returns, the sysfs attribute is gone and kernfs has
drained any in-flight show(), so no reader can touch cs84xx; the put still
runs before the host and ha are freed. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Reject non-SCSI SRB on status IOCB fast path
qla2x00_status_entry() filters out non-TYPE_SRB entries and the
SRB_NVME_CMD, SRB_BIDI_CMD and SRB_TM_CMD types, then falls through to a
SCSI fast path that assumes the command is an SRB_SCSI_CMD. The first
thing on that path, qla_chk_edif_rx_sa_delete_pending(), and the
subsequent handling both evaluate GET_CMD_SP(sp), i.e. sp->u.scmd.cmd.
The srb u union overlays the SCSI command pointer with other command
layouts (bsg_job, iocb_cmd). If firmware delivers an unexpected
STATUS_TYPE IOCB for a non-SCSI handle, sp->u.scmd.cmd can read as a
non-NULL garbage pointer, bypassing the NULL checks in
qla_chk_edif_rx_sa_delete_pending() and at the cp == NULL test, and
leading to a wild pointer dereference.
Reject any SRB whose type is not SRB_SCSI_CMD before entering the fast
path. The outstanding_cmds slot is left untouched so a genuinely
non-SCSI command still completes through its proper handler. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Quiesce response IRQ before freeing request queue
qla2xxx_delete_qpair() deletes the request queue before the response
queue. qla25xx_delete_req_que() frees the request queue memory
(kfree(req) in qla25xx_free_req_que()), but the response-queue MSI-X is
only released later, in qla25xx_free_rsp_que(). In that window the
response interrupt can still fire, qla2xxx_msix_rsp_q() queues
qpair->q_work, and qla_do_work() -> qla24xx_process_response_queue()
dereferences the now-freed rsp->req (LOGINOUT/CT/ELS entries and the
status path), a use-after-free.
The cancel_work_sync() added for the qpair teardown lives in the
response free path, which runs after the request queue is already freed,
so it does not protect rsp->req.
Release the response-queue interrupt and flush qpair->q_work before
deleting the request queue, so no late completion can reach the freed
request queue. Clearing have_irq makes the subsequent
qla25xx_free_rsp_que() skip its free_irq(), and the firmware
queue-delete order (request then response) is preserved; the
request-delete mailbox completes on the default vector and is unaffected
by dropping the qpair response interrupt early. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Avoid double completion in async IOCB timeout
qla2x00_async_iocb_timeout() tries to abort a timed-out async IOCB. When
qla24xx_async_abort_cmd() fails, both the SRB_LOGIN_CMD path and the
SRB_CTRL_VP/default path scan outstanding_cmds[] for the SRB and then
call sp->done(sp, QLA_FUNCTION_TIMEOUT) unconditionally, without checking
whether the SRB was actually found and removed.
If the response ISR completes the same handle first, it removes the SRB
under qp_lock_ptr and runs sp->done() -> complete(sp->comp). The
submitter qla24xx_control_vp() wakes from wait_for_completion(), clears
sp->comp, drops its reference and returns, reclaiming the on-stack
completion. The timer reference keeps the SRB alive across the timeout
handler, but not the submitter's stack. The timeout then issues a second
sp->done() -> qla_ctrlvp_sp_done(), which evaluates "if (sp->comp)
complete(sp->comp)"; with the pointer loaded before the submitter's NULL
store, complete() writes into the freed stack frame, a use-after-free.
Track whether this path removed the SRB from outstanding_cmds and only
call sp->done() when it did, so the command is completed exactly once by
whichever path owns it. This mirrors the sp_found guard already used in
qla24xx_abort_iocb_timeout(). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Bound rsp_info_len to avoid OOB sense-data read
In qla2x00_status_entry(), the FWI2 status path advances sense_data and
shrinks par_sense_len by rsp_info_len:
if (IS_FWI2_CAPABLE(ha)) {
sense_data += rsp_info_len;
par_sense_len -= rsp_info_len;
}
rsp_info_len is a 32-bit value taken directly from the target's FCP
response (sf.rsp_data_len), while par_sense_len is the IOCB data area
size (28 bytes for 24xx, 60 bytes for 29xx). A hostile or buggy target
reporting an rsp_info_len larger than par_sense_len makes the unsigned
subtraction underflow to a huge value and advances sense_data out of
bounds.
The underflowed par_sense_len then defeats the cap in
qla2x00_handle_sense():
if (sense_len > par_sense_len)
sense_len = par_sense_len;
memcpy(cp->sense_buffer, sense_data, sense_len);
so the memcpy reads up to SCSI_SENSE_BUFFERSIZE bytes from the
out-of-bounds sense_data pointer, leaking adjacent response-ring/heap
memory into the command's sense buffer.
Clamp rsp_info_len to par_sense_len before the subtraction so
par_sense_len can never underflow and sense_data stays within the IOCB
data area. The fix sits before the comp_status switch, covering both
qla2x00_handle_sense() call sites. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Hold vport_slock for host map update in report ID acquisition
qla24xx_report_id_acquisition() format-1 handling drops vport_slock after
taking the vport reference and then calls qla_update_host_map() without
the lock. That reaches qla_update_vp_map(), which mutates the ha->host_map
btree via btree_insert32()/btree_update32()/btree_remove32() and is
documented to require vport_slock to be held by the caller. Running it
unlocked can race concurrent host_map updates and corrupt the btree.
The format-2 path in the same function already wraps its host_map update
(SET_AL_PA) in vport_slock; the format-1 path is the lone outlier.
Hold vport_slock across the format-1 qla_update_host_map() call to honor
the documented locking contract. The vref_count taken in the loop keeps
the vport valid, so this only adds the missing host_map serialization. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: only redirty pinned folios in redirty_blocks
redirty_blocks() pins folios with read_cache_folio() and then walks the
same range again with filemap_lock_folio() to redirty them and drop the
references it took.
Commit 5951fee46bef ("f2fs: Use a folio in redirty_blocks()") changed
the second pass to a do/while loop. If read_cache_folio() fails before
anything is pinned, page_idx does not advance but the cleanup loop still
runs once.
If readahead has already populated the failed folio in page cache, that
extra iteration finds it and folio_put_refs(folio, 2) drops one
reference too many. Later drop_caches or reclaim can then report
"BUG: Bad page state".
Only redirty the range that was pinned successfully. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: validate MOVE_RANGE destination size
F2FS_IOC_MOVE_RANGE checks the source range, but not the destination end
before updating i_size. A source hole can expose this: __clone_blkaddrs()
skips NULL_ADDR entries and returns success, so the caller can still extend
the destination inode with unchecked pos_out + len.
Reject destination overflow and use inode_newsize_ok() before extending
the destination inode. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: limit recovery filename logging to stored length
F2FS stores recovery filenames as a length plus a fixed-size i_name
buffer. The buffer is not NUL-terminated, but recover_inode() and
recover_dentry() print it with %s.
For a 255-byte filename, recovery logging can read past i_name into the
following raw inode fields.
Print the name with a precision bounded by i_namelen and F2FS_NAME_LEN. |
