| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: ipc4-topology: Refresh copier IPC payload before widget setup
The ipc_config_data buffer for copier widgets is built once during
ipc_prepare (called from sof_pcm_setup_connected_widgets) and cached
for reuse. For host copiers this buffer contains the copier_data with
gtw_cfg.node_id (host DMA ID). For DAI copiers it additionally includes
a dma_config_tlv trailer with stream_id and dma_channel_id for HDA link
DMA.
On suspend/resume, both host and link DMA streams are released and
re-allocated with potentially different stream tags. The underlying
copier_data and dma_config_tlv structures are correctly updated by
host_config and sdw_hda_dai_hw_params respectively. However, since the
widget list (spcm->stream[].list) persists across suspend,
sof_pcm_hw_params skips sof_pcm_setup_connected_widgets and ipc_prepare
never runs again to rebuild ipc_config_data. The stale cached payload
is then sent to firmware with boot-time DMA channel assignments, causing
DMA channel conflicts that lead to firmware errors and crashes.
Fix this by refreshing copier_data and dma_config_tlv portions of
ipc_config_data in sof_ipc4_widget_setup right before the IPC message
is sent. This ensures the payload always reflects the current DMA state
regardless of whether ipc_prepare ran.
For DAI copiers, the gtw_cfg.config_length in copier_data is temporarily
inflated to include the TLV size (matching the ipc_config_data layout)
before copying, then restored, mirroring what
sof_ipc4_prepare_copier_module does when first building the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
samples/damon/mtier: fail early if address range parameters are invalid
The comment on top of `struct damon_region` clearly says that
For any use case, @ar should be non-zero positive size.
which is now verified in damon_verify_new_region() if the kernel is built
with DAMON_DEBUG_SANITY.
The WARN_ONCE() can be triggered if the mtier sample module is enabled
before node{0,1}_{start,end}_addr have been properly initialized, which is
obviously not good.
------------[ cut here ]------------
start 0 >= end 0
WARNING: mm/damon/core.c:217 at damon_new_region+0xf4/0x118, CPU#59: bash/341468
Call trace:
damon_new_region+0xf4/0x118 (P)
damon_set_regions+0xfc/0x3c0
damon_sample_mtier_build_ctx+0xe8/0x3a8
damon_sample_mtier_start+0x1c/0x90
damon_sample_mtier_enable_store+0x98/0xb0
param_attr_store+0xb4/0x128
module_attr_store+0x2c/0x50
sysfs_kf_write+0x58/0x90
kernfs_fop_write_iter+0x16c/0x238
vfs_write+0x2c0/0x370
ksys_write+0x74/0x118
__arm64_sys_write+0x24/0x38
invoke_syscall+0xa8/0x118
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x54/0x370
el0t_64_sync_handler+0xa0/0xe8
el0t_64_sync+0x1ac/0x1b0
---[ end trace 0000000000000000 ]---
Note that the same issue can happen if detect_node_addresses is true, and
node 0 or 1 is memoryless. Fix it together by checking the validity of
parameters right before damon_new_region() and fail early if they're
invalid. |
| In the Linux kernel, the following vulnerability has been resolved:
l2tp: fix tunnel and session refcount leak on seq_file release
In pppol2tp_proc_open() and l2tp_dfs_seq_open(), iteration state
(pd->tunnel and pd->session) is kept in seq_file private data to allow
iteration across multiple read() system calls.
However, if userspace closes /proc/net/pppol2tp or /sys/kernel/debug/l2tp/tunnels
before reading to end-of-file (EOF), any tunnel or session reference stored in
pd->tunnel / pd->session is left un-dropped when seq_file private data is freed.
Fix this by dropping any remaining pd->tunnel and pd->session references in
pppol2tp_proc_release() and l2tp_dfs_seq_release() when closing the file. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: finish crypto callback cleanup before peer release
Crypto completion callbacks hold both key-slot and peer references. The
peer reference pins the netdev, and dropping the last peer reference can
let netdev unregistration and module removal make progress.
Do not release that peer reference before the callback has finished its
own cleanup. If ovpn_crypto_key_slot_put runs after ovpn_peer_put, it can
schedule an RCU callback backed by module text after ovpn_cleanup
rcu_barrier has already run. The TX error path also freed the remaining
skb after ovpn_peer_put, leaving callback cleanup outside the peer/netdev
lifetime window.
Release the key slot and free any remaining skb first, then drop the peer
reference as the last callback action. |
| In the Linux kernel, the following vulnerability has been resolved:
af_unix: Unlink scc_entry in unix_del_edge().
Kyle Zeng reported that GC could free a dead SCC partially.
The scenario is as follows:
1) Create two SCCs:
X -. A <-> B
^--'
2) Run the following concurrently:
2-1) send() sk-B to sk-B from sk-X
2-2) close() both A and B
At 2-1), there is a small window where unix_add_edges()
publishes a new edge (B <-> B) to GC but its skb is not queued
by skb_queue_tail().
If 2-2) completes before skb_queue_tail() and GC is triggered,
it judges A <-> B as dead, but B is not freed because GC cannot
collect the not-yet-queued skb holding the B <-> B edge.
X -. A <-> B -. This edge is visible
^--' ^..' but skb is not
This itself is not a problem since the next GC run will judge
B as dead as well and free it finally.
X -. A <.> B -.
^--' ^--'
However, X's SCC forces the next GC to call unix_walk_scc_fast(),
and it iterates over A through B's scc_entry.
Let's unlink scc_entry before freeing the vertex in unix_del_edge(). |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: tegra - fix rctx->cryptlen calculation in tegra_gcm_do_one_req()
Perform rctx->cryptlen calculation in tegra_gcm_do_one_req() the same way
it is done in tegra_ccm_crypt_init(). The current formulae may lead to a
crash if a caller does not call tegra_gcm_setauthsize() and so ctx->authsize
remains zero. Then a decrypt operation with incorrect rctx->cryptlen will
lead to a write beyound rctx->dst_sg buffer.
As a follow-up cleanup delete struct tegra_aead_ctx->authsize field since
it appears to be completely unused. Also simplify tegra_ccm_setauthsize()
and tegra_gcm_setauthsize() functions respectively. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: core: Fix pointer desynchronization in fb_io_read()
In fb_io_read(), if copy_to_user() performs a partial copy (e.g., due to
a faulty user buffer), the loop adjusts the chunk size 'c' and updates
the remaining 'count'. However, the hardware 'src' pointer has already
been eagerly advanced by the original chunk size.
If the loop is allowed to continue, the read will resume from an
incorrect, over-advanced offset. Since the remaining 'count' was only
decremented by the successful bytes, this desynchronization causes the
next iterations to execute more hardware reads than originally bounded,
eventually leading to out-of-bounds I/O reads.
Fix this by breaking out of the loop immediately upon a partial
copy_to_user(). A partial copy indicates a faulty user buffer, making
subsequent read attempts futile. Breaking out ensures we return the
number of successfully read bytes without risking out-of-bounds hardware
accesses in subsequent mismatched iterations. |
| In the Linux kernel, the following vulnerability has been resolved:
block: stop the timeout timer when releasing a never added disk
disk_release() undoes blk_mq_init_allocated_queue() for a disk whose
probe failed before add_disk(), but it only calls blk_mq_exit_queue().
Nothing there stops q->timeout, and that timer rolls forward: it stays
pending until it next expires, not until the last request completes.
So if the driver issued any I/O before adding the disk, the
request_queue is freed while still linked into a timer wheel bucket.
Commit 6f8191fdf41d ("block: simplify disk shutdown") dropped the
blk_cleanup_queue() call that used to stop it. __del_gendisk() and
blk_mq_destroy_queue() still do; only the probe failure path lost it.
nvme gets there because nvme_update_ns_info() submits Report Zones or
FDP io-mgmt-recv on ns->queue before the disk is added, so a later
failure - a concurrent reset setting NVME_CTRL_FROZEN, or
device_add_disk() failing - lands in put_disk() with the timer armed:
BUG: KASAN: slab-use-after-free in detach_if_pending+0x30c/0x340
Write of size 8 at addr ffff888004d71310 by task kworker/u8:2/37
__timer_delete_sync+0x156/0x240 kernel/time/timer.c:1621
blk_sync_queue+0x22/0x40 block/blk-core.c:222
nvme_sync_queues+0x100/0x150 drivers/nvme/host/core.c:5362
nvme_reset_work+0x138/0x930 drivers/nvme/host/pci.c:3264
Allocated by task 34:
__blk_mq_alloc_disk+0x33/0x100 block/blk-mq.c:4462
nvme_alloc_ns+0x290/0x3870 drivers/nvme/host/core.c:4146
Freed by task 0:
blk_free_queue_rcu+0x3a/0x50 block/blk-core.c:254
rcu_core+0xc10/0x1730 kernel/rcu/tree.c:2857
The queue being synced there is ctrl->admin_q, only a victim sharing a
timer wheel bucket with the freed queue's dangling entry; other runs
tripped in enqueue_timer(), __run_timers() or blk_mq_timeout_work().
Failing nvme_alloc_ns() with a debug patch makes it deterministic: one
leaked timer trips KASAN within seconds, while 1987 patched releases
produced no splat.
Stop the timer and the queue work items before blk_mq_exit_queue(), like
blk_mq_destroy_queue() does.
Found by FuzzNvme. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: byd - synchronize timer deletion before freeing private data
byd_disconnect() uses timer_delete() before freeing the driver's private
data. This does not wait for a running byd_clear_touch() callback, which
dereferences the private data and its psmouse pointer. A callback racing
with disconnect can therefore access the private data after it has been
freed. The timer can also still be re-armed by byd_process_byte() while
the disconnect is in progress.
Use timer_shutdown_sync() before freeing the private data: it waits for
a running callback and turns any later re-arm attempt into a no-op. |
| In the Linux kernel, the following vulnerability has been resolved:
net: enetc: fix potential divide-by-zero when num_vsi is zero
For i.MX94 series, all the standalone ENETCs do not support SR-IOV, so
pf->caps.num_vsi is zero. This leads to a divide-by-zero in
enetc4_default_rings_allocation() when distributing rings among PF and
VFs.
Division by zero is undefined behavior in C. On ARM64, the UDIV/SDIV
instructions silently return zero rather than raising an exception, so
the issue does not cause a visible crash. However, relying on this
behavior is incorrect and poses a cross-platform compatibility risk.
Add an explicit check for num_vsi == 0 and return early after the PF's
rings have been configured. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: reclaim forward-allocated memory on RX path errors
After commit 9db5b3cec4ec ("mptcp: borrow forward memory from subflow"),
errors in the receive path prior to queueing skbs into the receive
queue do not trigger forward-allocated memory reclaiming.
Prevent forward memory from growing unboundedly in pathological drop
scenarios by explicitly reclaiming memory when skbs are dropped. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: dwc: Avoid dwc_pcie_rasdes_debugfs_deinit() NULL dereference when no RAS DES capability
dwc_pcie_rasdes_debugfs_init() returns success when the controller has no
RAS DES capability, leaving pci->debugfs->rasdes_info unset. The common
debugfs teardown path still calls dwc_pcie_rasdes_debugfs_deinit(), which
dereferences rasdes_info unconditionally.
Return early when no RAS DES state was allocated. In that case no RAS DES
mutex was initialized, so there is nothing to destroy.
[mani: reworded subject] |
| In the Linux kernel, the following vulnerability has been resolved:
s390/dasd: Fix potential NULL pointer dereference
dasd_release_space() checks the implementation of the is_ese()
discipline function before calling it to determine if a given device is
an ESE DASD.
The current usage of the logical AND operator will lead to a NULL
pointer dereference as the function is called even if the function
pointer is NULL.
Fix this by using the logical OR operator. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: use proper context for logging
The same as the rest of the code, get_ss_info_from_atombios() uses
calc_pll_cs->ctx->logger for logging. But calc_pll_cs->ctx is
initialized only later in calc_pll_max_vco_construct(). Therefore, any
output using DC_LOG_SYNC() leads to a NULL pointer deference in
get_ss_info_from_atombios().
According to Sashiko, the very same problem exists in
dce112_get_pix_clk_dividers() and dcn3_get_pix_clk_dividers() too.
To avoid accessing the NULL context, use clk_src->base.ctx->logger
everywhere. That context in base is initialized earlier in
dce110_clk_src_construct() and dce112_clk_src_construct(). Before
get_ss_info_from_atombios() or Sashiko's get_pix_clk_dividers functions
above are actually called. This is done by redefining DC_LOGGER to
CTX->logger.
Before:
dce110_clk_src_construct() did:
-> sets clk_src->base.ctx = ctx;
-> ss_info_from_atombios_create()
-> get_ss_info_from_atombios() <- uses calc_pll_cs->ctx # BOOM
-> calc_pll_max_vco_construct() <- sets calc_pll_cs->ctx
After:
dce110_clk_src_construct() does:
-> sets clk_src->base.ctx = ctx;
-> ss_info_from_atombios_create()
-> get_ss_info_from_atombios() <- uses clk_src->base.ctx
(cherry picked from commit 6f16fcbb0c46a87e3d9685407e906573d60104b0) |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_api: fix TOCTOU NULL deref on a->goto_chain
tcf_action_exec() handles TC_ACT_GOTO_CHAIN by first checking
rcu_access_pointer(a->goto_chain) and then calling
tcf_action_goto_chain_exec(), which does a second, independent
rcu_dereference_bh(a->goto_chain) read and immediately dereferences
chain->filter_chain. A concurrent tcf_action_set_ctrlact() (e.g. the gact
replace path) can clear a->goto_chain between the two reads, so the second
read returns NULL and tcf_action_goto_chain_exec() dereferences NULL.
Fix the race by doing a single rcu_dereference_bh() read of a->goto_chain
in tcf_action_exec(), checking it once for NULL, and passing the resulting
chain pointer into tcf_action_goto_chain_exec(). This turns the split
check/use into a single check/use on one value. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Pad trailing CCA or EP11 message with zeros
The both functions xcrb_msg_to_type6cprb_msgx() and
xcrb_msg_to_type6_ep11cprb_msgx() copy the user space message into a
kernel buffer based on the message length. But on further processing
the message is supposed to be 4 byte length adjusted. Thus up to 3
bytes of uninitialized kernel memory are forwarded to further
processing steps and may unwanted expose kernel memory to the crypto
card firmware.
This patch contains code to pad the gap between user space copied
message and message buffer length sent down to further processing of
the CCA or EP11 message to zeros. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Improve EP11 CPRB domain handling with ASN.1 parsing
The zcrypt_msgtype6_send_ep11_cprb() function uses fragile struct
overlays to access and modify the domain field in the EP11 CPRB
payload, creating maintainability and security concerns:
1. Struct overlay approach (pld_hdr) assumes fixed payload structure
and doesn't validate the actual ASN.1 encoding.
2. Complex length format detection logic is error-prone and doesn't
properly validate bounds at each parsing step.
3. Direct struct member access bypasses proper ASN.1 validation.
Fix by replacing struct overlays with explicit ASN.1 parsing that
validates each field (payload tag/length, function tag/length/value,
optional domain tag/length/value) with proper bounds checking at every
step. Add asn1_int_encode() helper function to safely write integer
values with correct endianness conversion. This makes the code
consistent with the validation pattern introduced with the rework of
the xcrb_msg_to_type6_ep11cprb_msgx() function. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/vfio_ccw: Selectively expand io_mutex
The io_mutex was defined to serialize the io_regions, but then has
also sort of been associated with the I/O themselves because of
the close relationship they share.
With the handful of races that are possible, the choices are either to:
A) expand the scope of io_mutex to close these remaining windows, or
B) reduce the scope of io_mutex to just io_region, and introduce a new
lock mechanism for the remaining I/O resources
This patch implements A, since B brings with it a lot more interactions
that would need to be tracked and kept in a correct hierarchy. It also
takes advantage of the workqueue element for cp_free() that now gets
called out of fsm_notoper(), which could be invoked out of an interrupt
context and thus cannot acquire a mutex itself. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/vfio_ccw: Move cp cleanup out of not operational
The fsm_notoper() routine is called when the device has been
lost, and is (by definition) no longer operational. Since this
can happen asynchronously from the normal behavior of the
driver, the cleanup may happen when holding other locks
in the calling sequence (notably, the cio subchannel lock).
Push the cleanup of the private->cp resources to a workqueue,
where it can be done out from under that lock sequence and
a future patch can safely manage the locking requirements. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ims-pcu - fix potential infinite loop in CDC union descriptor parsing
The driver parses CDC union descriptors in ims_pcu_get_cdc_union_desc()
by iterating through the extra descriptor data. However, it does not
verify that the bLength of each descriptor is at least 2. A malicious
device could provide a descriptor with bLength = 0, leading to an
infinite loop in the driver.
Add a check to ensure bLength is at least 2 before proceeding with
parsing. |
