| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Validate BSG request_len before reading vendor_cmd[]
The FC BSG transport allocates job->request via memdup_user() using the
exact user-supplied request_len. For FC_BSG_HST_VENDOR,
fc_bsg_host_dispatch() only guarantees request_len covers msgcode and
vendor_id; it does not account for the vendor_cmd[] flexible array.
qla2xxx then reads the command selector vendor_cmd[0] and, in several
sub-handlers, vendor_cmd[1]/[2] or structures overlaid on the vendor
command area without verifying request_len. A caller holding
CAP_SYS_RAWIO can submit a short request whose vendor_id matches the
host, triggering out-of-bounds heap reads (KASAN-detectable, and able to
mis-select a command or panic).
Add a central guard in qla2x00_process_vendor_specific() so the selector
is always in bounds, restrict the early vendor_cmd[0] read in
qla24xx_bsg_request() to sufficiently long vendor messages, and add
request_len checks to the sub-handlers that read further:
qla24xx_proc_fcp_prio_cfg_cmd(), qla2x00_process_loopback(),
qla84xx_reset(), qla84xx_updatefw(), qla2x00_read_optrom(),
qla2x00_update_optrom(), qlafx00_mgmt_cmd() and
qla28xx_validate_flash_image(). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix use-after-free of qpair work on queue teardown
The response queue MSI-X handler qla2xxx_msix_rsp_q() schedules
qla_do_work() via queue_work(ha->wq, &qpair->q_work). qla_do_work()
dereferences the qpair (vha, rsp) and takes qpair->qp_lock.
During teardown, qla2xxx_delete_qpair() deletes the response queue, which
calls free_irq() in qla25xx_free_rsp_que(), and then frees the queue and
the qpair. free_irq() waits for running hardirq handlers but does not
cancel work already placed on ha->wq. A still-pending q_work then runs
qla_do_work() against the freed qpair and response queue, causing a
use-after-free. This is especially likely during full adapter teardown,
where destroy_workqueue(ha->wq) forces pending work to run after the queue
pairs have been freed.
Flush the work item with cancel_work_sync() in qla25xx_free_rsp_que()
after free_irq() has released the interrupt (so no new work can be
queued) and before the response queue and qpair memory are freed (so the
flushed handler still sees valid memory). Guard on rsp->qpair and ha->wq
to match the INIT_WORK() condition and avoid operating on an
uninitialized work_struct. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: destroy seen inode bitmap when we fail to add a dirpath
LOLLM observes a memory leak in xchk_dirtree_create_path if we create
the directory path object but appending the name to the path fails.
When this happens, we don't tear down the (empty) seen inode bitmap.
This is a pretty trivial error, but let's not leave logic bombs.
Do the same for a similar bug in xrep_dirtree_create_adoption_path. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix exchange-range reflink flag clearing issue with INO1_WRITTEN
When exchanging two full-file ranges, xmi_can_exchange_reflink_flags()
can move the reflink inode flag from the file that currently has it to
the other file, as long as exactly one side is marked. This assumes
that the file contents, and therefore all shared extents, are exchanged.
That assumption is not true when XFS_EXCHMAPS_INO1_WRITTEN is set.
xfs_exchmaps_can_skip_mapping() can skip hole and unwritten mappings
from file1, so an exchange can complete without moving every mapping
that the earlier flag-swap decision accounted for. In that case the
post-operation cleanup can clear the reflink flag from an inode that
still owns shared written extents. Later writes then take the
non-reflink write path and may update blocks that should still have
been protected by CoW, which shows up as data corruption between
reflink-related files.
Fix this by disabling the reflink flag exchange whenever
XFS_EXCHMAPS_INO1_WRITTEN is requested. The contents exchange can still
proceed; the conservative outcome is that both inodes keep the reflink
flag. The regular reflink flag cleanup path can drop the extra flag
later once the inode no longer has shared extents. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix unit conversions in per_binval computation
LOLLM noticed that we're doing the unit conversion in the per_binval
computation backwards -- xfs_buf_inval_log_space's second parameter is
supposed to be in bytes, but max_binval is in units of fsblocks. Hence
the conversion should be FSB -> B, not the other way around. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: avoid leaking refcount in cifs_queue_oplock_break()
cifs_queue_oplock_break() unconditionally takes a reference on the
target file before queueing cifs_oplock_break(). Only that work item
decreases the reference counter again.
If another oplock break arrives while that work is still queued,
queue_work() will return false and not queue this second work item. As a
result, we will never reach the point to drop the file reference again
and are leaking this reference. This can be triggered when interacting
with a slow-responding server.
As a result, later unmount operations for this file system will fail with
BUG: Dentry ... still in use (1) [unmount of cifs cifs]
VFS: Busy inodes after unmount of cifs (cifs)
kernel BUG at fs/super.c:777!
Fix this by only incrementing the reference count if the work has been
queued successfully. Taking it after queue_work() is safe because all
three callers hold tcon->open_file_lock across the call and
_cifsFileInfo_put() decrements under that same lock, so a worker that
starts the handler in the window cannot drop the reference before it has
been taken. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: preserve LZMA decoders on resize failure
The pool-resize path frees each stream's old decoder before allocating
its replacement. If an allocation fails after some streams have already
been replaced, the failed stream is put back on the list with state ==
NULL. z_erofs_lzma_max_dictsize is still advanced as if the whole
pool had been resized.
An existing LZMA mount can select the broken stream and pass
NULL to xz_dec_microlzma_reset(). A retry at the same size also
skip another resize attempt. Since the global maximum was advanced,
thus, the invalid state is left unrepaired.
Allocate each replacement before freeing the old decoder, temporarily
retaining one old decoder during allocation. Stop at the first failure
and advance z_erofs_lzma_max_dictsize only after all streams satisfy
the request.
Record each stream's dictionary capacity so retries can skip streams
already enlarged before a partial failure. |
| In the Linux kernel, the following vulnerability has been resolved:
ufs: create the root dentry after loading cylinder metadata
ufs_fill_super() installed sb->s_root before it loaded the cylinder
group structures for a writable mount:
sb->s_root = d_make_root(inode);
...
if (!sb_rdonly(sb))
if (!ufs_read_cylinder_structures(sb))
goto failed;
When ufs_read_cylinder_structures() failed, the error path freed the
in-core superblock information and set sb->s_fs_info to NULL while
sb->s_root stayed installed. get_tree_bdev() then reached
deactivate_locked_super(), and because s_root was present,
generic_shutdown_super() called sync_filesystem() and the put_super
operation. Both dereference UFS_SB(sb), which is now NULL, so a mount
that fails only while reading the cylinder groups oopses during
teardown. A crafted image whose first cylinder group cannot be read
reaches this path.
Load the cylinder group metadata first and create the root dentry last,
so the superblock is published to the VFS only once it is fully set up.
ufs_setup_cstotal() and ufs_read_cylinder_structures() take only the
super_block and do not use the root inode, so the reordering is safe. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Fix ineffective error check in nested domain allocation
amd_iommu_pdom_id_alloc() returns an int: a domain ID on success, or the
negative errno from ida_alloc_range() when the ID space is exhausted or
memory is short. amd_iommu_alloc_domain_nested() stores that return value
in gdom_info->hdom_id, which is a u32, and only then tests it:
gdom_info->hdom_id = amd_iommu_pdom_id_alloc();
if (gdom_info->hdom_id <= 0) {
The assignment discards the sign, so -ENOSPC becomes 0xffffffe4 and the
test never fires. The nested domain is then set up with a host domain ID
that was never allocated, instead of the allocation failing with -ENOSPC.
Keep the value in an int, test it there, and store it only once it is
known to be valid, which is what the other amd_iommu_pdom_id_alloc()
callers already do. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: sr: restore network header before routing and forwarding
ipv6_srh_rcv() runs with skb->data at the Segment Routing Header (SRH)
while skb_network_header() points at the IPv6 header.
When segments_left > 0, ipv6_srh_rcv() previously restored the skb->data
position by pushing sizeof(struct ipv6hdr), assuming the SRH immediately
followed the fixed IPv6 header. If another extension header (such as a
Hop-by-Hop options header) precedes the SRH, skb_network_offset()
remained negative.
This led to two problems:
1. During ip6_route_input(), fib6_rules_early_flow_dissect() invokes
__skb_flow_dissect() which passes the negative skb_network_offset()
to flow dissection, breaking BPF and C flow dissector logic.
2. If forwarded via ip6_forward() or redirected via act_mirred, downstream
handlers (like sch_fragment() or neighbour output) pass the negative
offset as an unsigned length, triggering OOB memcpy or buffer overflows.
Fix this by pushing -skb_network_offset(skb) before routing, ensuring
skb_network_offset(skb) is 0 for route lookup / flow dissection as well as
downstream forwarding. On the loopback path, pull skb_transport_offset(skb)
to restore skb->data to the SRH before looping back. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: safely drain sessions during logoff
SMB3 multichannel allows requests for one session to run on multiple
connections. Wait for all channels bound to a session before freeing
shared session objects.
A deferred byte-range lock remains counted as a running request and only
wakes when its file closes. Wake blocked locks during the drain without
unpublishing or modifying their file objects. Synchronous CANCEL requests
must invoke their cancellation callback to wake pending operations, while
CHANGE_NOTIFY completion remains specific to the asynchronous path.
Serialize session teardown with channel registration and previous-session
cleanup, and use atomic work-state transitions so LOGOFF, CANCEL, and
connection teardown invoke cancellation callbacks only once. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: mdb: Fix use-after-free in vxlan_mdb_remote_src_del()
vxlan_mdb_is_valid_source(), which validates MDBE_ATTR_SOURCE and every
MDBE_ATTR_SRC_LIST member, accepts the all-zeros address.
A source list is only accepted on a (*, G) entry, whose source is the
all-zeros address, and for each member of the list an (S, G) entry is
derived from it by substituting the source. Entries are keyed by a plain
memcmp() of struct vxlan_mdb_entry_key, so if MDBE_ATTR_SOURCE is present
and holds the all-zeros address and the source list holds it as well, the
derived (S, G) key is byte-identical to the (*, G) key and resolves to the
same entry. Omitting MDBE_ATTR_SOURCE is not equivalent, as the key is
then left with a zero address family.
vxlan_mdb_remote_src_del() removes the forwarding entry of a source before
freeing the source entry:
vxlan_mdb_remote_src_fwd_del(vxlan, group, remote, &ent->addr);
vxlan_mdb_remote_src_entry_del(ent);
With the keys aliased, the first call deletes the remote of the entry that
owns 'ent' instead of a separate (S, G) entry, and frees 'ent'. The second
call then runs on the freed entry, and its hlist_del() reads ->pprev and
->next out of it and writes through them.
Adding the (*, G) entry with NLM_F_REPLACE and no source list marks the
all-zeros source for deletion and reaches this from the sweep at the end
of vxlan_mdb_remote_srcs_replace().
BUG: KASAN: slab-use-after-free in __vxlan_mdb_add+0x1cd/0xd70
Read of size 8 at addr ffff888102852500 by task poc/84
__vxlan_mdb_add+0x1cd/0xd70
vxlan_mdb_add+0xc0/0x140
rtnl_mdb_add+0x157/0x2a0
rtnetlink_rcv_msg+0x207/0x5a0
Allocated by task 84:
__kmalloc_cache_noprof+0x153/0x360
vxlan_mdb_remote_srcs_add+0x2eb/0x440
__vxlan_mdb_add+0x803/0xd70
Freed by task 84:
kfree+0x14c/0x3b0
vxlan_mdb_remote_del+0x129/0x1a0
__vxlan_mdb_del+0x4f/0xe0
vxlan_mdb_remote_src_fwd_del.isra.0+0x162/0x1b0
__vxlan_mdb_add+0x1c5/0xd70
The MDB operations are netns-scoped, so an unprivileged user can perform
them in a new user and network namespace.
Reject the all-zeros address in vxlan_mdb_is_valid_source(), which covers
both call sites. A (*, G) entry is expressed by omitting the source, so
nothing legitimate is refused.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
accel: ethosu: Don't read the U65 rounding mode as a storage mode
Bits 15:14 of NPU_SET_{IFM,OFM}_PRECISION select the activation storage
mode on U85 only. On U65 the same field holds the rounding mode, and the
command stream parser has read it as a storage mode since the driver was
added.
That went unnoticed while unknown values fell through the switch, but
now that they are rejected, every U65 command stream that asks for
natural rounding (2) fails CMDSTREAM_BO_CREATE with -EINVAL. Mesa emits
it for average pooling, concatenation, split, unpack, strided slice, LUT
and argmax, which is 72 failures of the Teflon test suite on an i.MX93.
Truncating rounding (1) is misread as well: it picks the two-tile
address path and computes a bogus feature map size from tile bases the
command stream never set.
Read the field as a storage mode only on the hardware where it is one. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix BPF_F_CPU validation for sparse CPU IDs
BPF_F_CPU stores the target CPU ID in the upper 32 bits of the map
operation flags. bpf_map_check_op_flags() currently compares that ID
with num_possible_cpus(), which is the number of possible CPUs rather
than a bound on CPU IDs.
On an arm64 QEMU guest with a CPU device-tree hole, the possible CPU
mask was 0,2-3. A userspace program using raw bpf() syscalls creates
a BPF_MAP_TYPE_PERCPU_ARRAY and performs update and lookup operations
for each CPU by setting BPF_F_CPU and the CPU ID in the flags.
With the old check, CPU 1 is incorrectly accepted while valid CPU 3 is
rejected with -ERANGE. The CPU 1 update then reaches the per-CPU map
access path and triggers:
Unable to handle kernel paging request at virtual address ...
pc : __pi_memcpy_generic+0x5c/0x22c
lr : bpf_percpu_array_update+0x2dc/0x2e8
Call trace:
__pi_memcpy_generic
bpf_map_update_value
map_update_elem
__sys_bpf
Check the CPU ID against nr_cpu_ids and cpu_possible() instead. This
rejects CPU IDs outside the valid range and CPUs absent from the
possible mask, while allowing valid sparse CPU IDs. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: use the DMA API for resource backing on Xen
On a Xen PV domain page addresses bear no relation to the real machine
addresses the host would have to use to reach it.
virtio_ring.c handles this correctly, vring_use_map_api() returns true
for any xen_domain() regardless of VIRTIO_F_ACCESS_PLATFORM.
virtio-gpu makes the same decision independently, but its copy
looks only at the feature bit:
bool use_dma_api = !virtio_has_dma_quirk(vgdev->vdev);
QEMU does not set iommu_platform on virtio-vga by default, so
VIRTIO_F_ACCESS_PLATFORM is not negotiated, use_dma_api is false, and
virtio_gpu_object_shmem_init() describes the framebuffer's backing pages
to the host with sg_phys(). Those are guest-physical addresses. In a PV
domain they resolve, on the host side, to pages belonging to some other
domain, so the host scans out unrelated memory.
Move the decision into virtio_gpu_use_dma_api() and give it the
xen_domain() check, like vring_use_map_api() has. This
additionally enables the dma_sync_sgtable_for_device() calls in
virtgpu_vq.c, which are required for correctness whenever swiotlb
is in play.
Reproduced with a Xen 4.21 PV dom0 nested inside QEMU 8.2 with
virtio-vga, on both a distro 6.8 kernel and 6.18 LTS. A PVH dom0
works fine and doesn't need this fix because it is identity-mapped,
only PV dom0s are affected. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (ltc4282) Make sure clk_init_data is fully initialized
The clk_init_data structure contains several mutually-exclusive members
for different methods to specify the possible parents of a clock,
prompting drivers to initialize only the members they need. However,
not initializing all members may cause subtle issues, which are only
exposed when CONFIG_INIT_STACK_ALL_PATTERN or CONFIG_INIT_STACK_NONE is
enabled.
ltc428_clk_provider_setup() does not fill in any parent clocks, and
assumes that init.num_parents is NULL. However, the latter in
uninitialized, and thus may cause a crash.
Make sure all members are fully initialized, to fix such bugs, and to
avoid future breakage when converting drivers to a different method for
specifying the parents. |
| A flaw was found in evolution-data-server. Inconsistent comparison logic in the addressbook file backend allows a Flatpak application with D-Bus access to craft a malicious URI containing directory traversal sequences. This URI is stored without proper validation during contact creation or modification. Later, during contact deletion, the URI is processed with a less strict check, leading to the deletion of arbitrary files on the host filesystem. This could potentially include critical Flatpak override files. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (asus_rog_ryujin) Validate HID report lengths
rog_ryujin_raw_event() parses response headers and payload fields without
first checking that they are present in the received report. A short report
can therefore make the driver consume uninitialized bytes from the HID
transport buffer and expose them as sensor values through sysfs.
Validate the response header and the fields used by each response type
before parsing them. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject out-of-bounds DataOffset in CIFSSMBRead()
The SMB1 synchronous read helper CIFSSMBRead() validates the server's
DataLength against CIFSMaxBufSize and the caller's count, but never
validates DataOffset. The copy source is formed as
&pSMBr->hdr.Protocol + le16_to_cpu(pSMBr->DataOffset)
and memcpy()'d for DataLength bytes with no check that the
[DataOffset, DataOffset + DataLength) range lies within the response
actually received from the server.
A malicious or compromised SMB1 server can return a response carrying
an in-range DataLength and a large DataOffset, driving the source
pointer past the end of the response buffer. The memcpy() then copies
adjacent kernel heap into the caller's read buffer (information
disclosure), or reads unmapped memory and oopses (denial of service).
SMB1 is not negotiated by default; reaching this code requires an
explicit vers=1.0 mount.
Both DataOffset and the received response length recorded in
rsp_iov.iov_len are relative to the start of the SMB header, so reject
the response unless DataOffset + DataLength fits within that length,
using overflow-safe arithmetic, before forming the source pointer.
The response length has been validated by the previous patch, so the
DataOffset and DataLength fields can be read safely here.
While here, make data_length unsigned. It holds a length derived from
unsigned on-the-wire fields and is only ever compared against unsigned
quantities; print it with %u accordingly, and add __func__ to the
cifs_dbg() calls in this function. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Prevent queue stop with deferred completions
When the driver receives a burst of packets, it can mark a BD with the
NO_CMPL bit to defer completions. The expectation is that the last
packet in the ring will have this bit unset and the completion generated
by that packet will cleanup that packet and the ones preceding it. This
helps to reduce the number of completions fired.
The suppressed completions are controlled by the driver and the number
of packets with suppressed completions scales with the size of the ring.
SW USO packets, on the other hand, have an upper bound on the maximum
number of BDs which can be consumed which does not scale with the ring
size.
So, for small rings it is possible that: a burst of packets is handed to
the driver, the driver defers completions for all of the packets because
the number of free descriptors stays above the threshold in the driver.
Then, a USO packet arrives, but the number of BDs available is not
enough and the USO code exits early.
In this case, you end up in a state where the ring is full of packets
with their completions suppressed, which can cause the queue to stop and
never be restarted.
Assuming default CONFIG_MAX_SKB_FRAGS, this is only possible for small
rings (<= 457 descriptors, below the driver default value) when
a burst of packets fills the ring, followed by a large USO packet that
can't fit. For larger rings, the delta between the completion
suppression threshold and the BDs required for SW USO is large enough
that completions will fire and this case is unreachable.
This issue was pointed out by Sashiko and while it seems fairly unlikely
given that the queue size must be small to trigger this, it is indeed
possible.
Fix this by tracking the last BD which deferred completions and
centralizing the logic for deciding when to ring the doorbell. The NO_CMPL
bit is now cleared in bnxt_txr_db_kick(), so every doorbell site is
covered, including the SW USO early exit. This guarantees the ring always
ends in a BD which generates a completion to clean it and wake the queue. |
