| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
s390/vfio-ap: Fix NULL deref in status_show() during queue probe
When vfio_ap_mdev_probe_queue() creates the sysfs attribute group,
the queue's driver data has not yet been set. A concurrent read of
the 'status' attribute can therefore call dev_get_drvdata() and
get NULL, which is then passed directly to
vfio_ap_mdev_for_queue() where q->apqn is unconditionally
dereferenced, causing a NULL pointer dereference.
Fix this by acquiring the update locks before calling
sysfs_create_group(). The status_show() function acquires
guests_lock before reading the driver data, so any concurrent
read will block until after dev_set_drvdata() has been called
and the update locks are released.
As a bonus, the APQN no longer needs to be read from the queue
struct after allocation — it can be read directly from apdev
before allocation and stored in a local variable, which is then
assigned to q->apqn once the allocation succeeds. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: mtdoops: free page bitmap when the backing MTD is removed
mtdoops_notify_add() allocates oops_page_used when the configured MTD
device is registered. mtdoops_notify_remove() detaches from that device
but leaves the bitmap allocated. If the same MTD device is later
registered again, the add path allocates a new bitmap and overwrites the
old pointer, leaking one vmalloc allocation per remove/add cycle.
This is only visible when the backing MTD device can disappear and be
registered again while mtdoops remains loaded, so the usual static MTD
case does not expose it.
Free the bitmap after unregistering the dumper and flushing the pending
workers, then clear the pointer and page count before a later attach can
allocate fresh state. Clearing the pointer also keeps the module exit
path from freeing the same bitmap a second time after a remove event. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: rawnand: validate ONFI extended parameter page sections
nand_flash_detect_ext_param_page() allocates the length declared by the
ONFI parameter page, then treats the data as a fixed header followed by
variable-length sections. It reads that header and advances over sections
without first proving that the fixed page and each current section fit in
the allocation.
Reject pages shorter than the fixed header, track the remaining variable
area while walking sections, and require the ECC section to contain every
field read from struct onfi_ext_ecc_info. Use device-scoped diagnostics
that identify the malformed ONFI section. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: mcast: linearize skbuff for packet generation
batadv_mcast_forw_packet() and batadv_mcast_forw_scrape() is not only
called (indirectly) by the unsharing+linearizing batadv_recv_mcast_packet()
handler. When it is called (indirectly) by batadv_mcast_forw_mcsend() then
it will be unshared but not linearized. The SKB_LINEAR_ASSERT() can
therefore cause a fatal BUG().
The linearization should happen during the expansion of the head because
the scrape function can be hit already during the initial
batadv_mcast_forw_mode() selection code:
* batadv_interface_tx
* batadv_mcast_forw_mode
* batadv_mcast_forw_mode_by_count()
* batadv_mcast_forw_push()
-> calls batadv_mcast_forw_expand_head() before everything else
* batadv_mcast_forw_push_tvlvs()
* batadv_mcast_forw_push_dests()
* batadv_mcast_forw_push_adjust_padding()
* batadv_mcast_forw_scrape() |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: dat: avoid unaligned fault in IP extraction
Independent of the alignment of the ARP packet in the SKB, either the
batadv_arp_ip_src or the batadv_arp_ip_dst will have an unaligned access
(on HW without native unaligned read support).
Use get_unaligned() to handle this properly on all architectures. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: bla: fix freeing of claims on meshif deletion
When the mesh interface is getting deleted, then
batadv_bla_del_backbone_claims() (via batadv_bla_purge_backbone_gw()) could
make sure that all claims gets removed. But this function is only executed
when bat_priv->bla.claim_hash is not NULL. And since batadv_bla_free() is
always setting it to NULL before it is (indirectly) called, it was never
actually executed.
But the batadv_bla_purge_claims() -> batadv_handle_unclaim() is at the
moment too fragile because the BLA code is not handling the rehashing in
batadv_bla_update_orig_address(). The stored backbone address doesn't have
to be the one actually used for the hash bucket selection during the
initial adding of the backbone. The batadv_handle_unclaim() can therefore
fail to find the respective backbone for the unclaim and then stop the
deletion.
But the actual backbone_gw object is not needed for the unclaim because all
relevant information is always provided by the caller. And the check for
the existence of the backbone_gw doesn't provide any additional security
check for the deletion of a claim. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: cs35l33: drain threaded IRQ before runtime suspend
cs35l33_runtime_suspend() currently switches the codec into
regcache_cache_only(true) and powers it down without first quiescing the
threaded IRQ registered by devm_request_threaded_irq(). That leaves a
window where cs35l33_irq_thread() can still run after suspend has closed
off live register access.
A running system can reach this during runtime PM while the driver still
has critical fault IRQs unmasked. If the threaded handler runs in that
window, it reads volatile INT_STATUS_1/2 after cache_only has been
enabled, ignores the regmap_read() failures, and can still drive the
AMP_SHORT_RLS, CAL_ERR_RLS, OTE_RLS, and OTW_RLS release paths.
Use disable_irq() before entering cache_only/power-off so any in-flight
threaded handler is drained and no new IRQ thread can run during the
suspended state. Re-enable the IRQ only after runtime_resume() has
restored live register access with regcache_sync(). Since probe only
warns if devm_request_threaded_irq() fails, track whether the IRQ was
actually installed before disabling or re-enabling it. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: cs35l34: drain threaded IRQ before runtime suspend
cs35l34_runtime_suspend() currently switches the codec into
regcache_cache_only(true), asserts reset low, and powers the device off
without first quiescing the threaded IRQ registered by
devm_request_threaded_irq(). That leaves a window where
cs35l34_irq_thread() can still run after suspend has removed live
hardware access.
A running system can reach this during runtime PM while the driver still
has critical fault IRQs unmasked. If the threaded handler runs in that
window, it reads volatile INT_STATUS_1..4 after cache_only has been
enabled, ignores the regmap_read() failures, and can still execute the
PROT_RELEASE_CTL release sequence or the BST fault power-down writes.
Use disable_irq() before entering cache_only/reset-low/power-off so any
in-flight threaded handler is drained and no new IRQ thread can run
while the device is suspended. Re-enable the IRQ only after
runtime_resume() has restored live register access with regcache_sync().
Since probe only logs request_threaded_irq() failures and keeps going,
track whether the IRQ was actually installed before disabling or
re-enabling it. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: hdac_hda: Fix hlink refcount leak on component registration failure
hdac_hda_dev_probe() gets the HDA link with snd_hdac_ext_bus_link_get()
before registering the ASoC component. If component registration fails,
the function returns without dropping the link reference.
Always call snd_hdac_ext_bus_link_put() after the registration attempt so
the reference taken during probe is balanced on both success and failure. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: atlas-sensor: fix PM reference leak in buffer postenable
atlas_buffer_postenable() acquires a runtime PM reference with
pm_runtime_resume_and_get() but returns the result of
atlas_set_interrupt() directly. If atlas_set_interrupt() fails,
the runtime PM reference is leaked and the device can never
autosuspend.
Add pm_runtime_put_autosuspend() on the error path to balance
the reference. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: sgp30: Handle IAQ thread creation failure
kthread_run() can fail and return an error pointer, but sgp_probe() stores
it and returns success, so the device is registered without its IAQ thread
and sgp_remove() later passes the error pointer to kthread_stop(). Return
the error from probe instead. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: dac: m62332: Fix regulator reference count imbalance
m62332_set_value() enables the Vcc regulator on every write of a
non-zero value and disables it on every write of zero, without tracking
the channel's current state. Because the regulator is reference counted,
changing a channel directly from one non-zero value to another enables
it more than once, while a later write of zero disables it only once.
The reference count never returns to zero and the regulator is left
enabled indefinitely.
Only enable the regulator on the transition from zero to non-zero, and
only disable it on the transition from non-zero to zero, using the
previously stored channel value to detect the edge. Balance the
regulator on the I2C error path so the reference count stays consistent
if the write fails. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: apds9306: fix PM reference leak in apds9306_read_data()
apds9306_read_data() calls pm_runtime_resume_and_get() but several
error paths return directly without calling pm_runtime_put_autosuspend(),
leaking the runtime PM reference and preventing the device from
autosuspending.
Use PM_RUNTIME_ACQUIRE_AUTOSUSPEND() and PM_RUNTIME_ACQUIRE_ERR() to
automatically handle runtime PM reference release on all return paths. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: ltrf216a: fix runtime PM reference leak in error path
ltrf216a_get_lux() acquires a runtime PM reference by calling
ltrf216a_set_power_state(data, true). However, if
ltrf216a_read_data() fails, the function returns immediately without
dropping the reference.
This leaves the runtime PM usage count unbalanced, preventing the device
from autosuspending after a failed read.
Fix this by releasing the runtime PM reference before returning from the
error path. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: pressure: dps310: fix NULL pointer dereference on ACPI probe
When the device is enumerated through its ACPI HID (IFX3100),
i2c_client_get_device_id() returns NULL: the ACPI-derived client name
does not match the driver's i2c_device_id table. dps310_probe() then
dereferences that NULL pointer in "iio->name = id->name" and crashes the
kernel during probe.
The IIO device name is always "dps310", so set it directly and drop the
now-unused device-id lookup. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nVMX: Ensure KVM_REQ_GET_NESTED_STATE_PAGES is cleared on VM-Exit
Always check and clear KVM_REQ_GET_NESTED_STATE_PAGES when emulating a
nested VM-Exit to ensure the request is cleared, even when KVM was built
with CONFIG_KVM_HYPERV=n, as KVM subtly relies on the "check" to clear
the flag and thus avoid double-mapping the vmcs12 pages, e.g. if KVM
manages to bail from VM-Enter without processing the request, and then
emulates VMLAUNCH or VMRESUME. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Fix length check __import_wp_info()
struct kvm_hw_breakpoint::len is a __u64 that is fully controlled by user
space. This is then assigned to wp_info->len, which is an int. The bounds
check is done on the truncated value while the allocation uses the
untruncated one:
wp_info->len = bp_data->len;
[...]
if (wp_info->len < 0 || wp_info->len > MAX_WP_SIZE)
return -EINVAL;
wp_info->old_data = kmalloc(bp_data->len, GFP_KERNEL_ACCOUNT);
Use the validated value for the allocation as intended. Without this
fix userspace can trigger >4GB allocations which will fail and result
in a WARN due to MAX_PAGE_ORDER. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Fix memory leak in guest debug handling
bp_data is freed only for the error case by kfree(bp_data).
Every successful KVM_SET_GUEST_DEBUG will leak bp_data. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Fix old_data leak in guest debug error path
__import_wp_info() allocates a per-watchpoint old_data buffer to back up
the original guest memory contents. If a later watchpoint of the same
KVM_SET_GUEST_DEBUG request fails to import, kvm_s390_import_bp_data()
jumps to the error label, which frees the wp_info array but not the
old_data buffers of the entries that were imported successfully. Up to
MAX_BP_COUNT - 1 buffers of up to MAX_WP_SIZE bytes are leaked per failed
request, and the request can be repeated.
Create error handling for cleaning up all created old_data memory
areas. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Free guest debug data on vcpu destroy
kvm_s390_clear_bp_data() is only called from
kvm_arch_vcpu_ioctl_set_guest_debug(), i.e. when user space changes or
disables debugging. A vCPU that is destroyed while hardware breakpoints
are still armed - the normal case when the VMM just exits or crashes -
leaks hw_bp_info, hw_wp_info and all old_data buffers, since generic KVM
frees the vCPU right after kvm_arch_vcpu_destroy().
That is bounded by MAX_BP_COUNT entries, so roughly 8 KiB per vCPU, but
it is unbounded over VM lifetimes. The allocations are
GFP_KERNEL_ACCOUNT, so the charge also outlives the exiting process and
pins dying memcgs.
Fix by clearing the debug data on vCPU destruction. Calling it
unconditionally is fine: struct kvm_vcpu is zero allocated, so for a vCPU
that never enabled debugging the counters are 0 and the pointers NULL. |
